SunBriteTV TV Mount SBWM46 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
All-Weather Articulating Wall Mount  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
SB-WM46  
 
Installation Instructions  
SB-WM46  
DIMENSIONS  
7.87  
200.0  
3
 
SB-WM46  
Installation Instructions  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Potloodmerkteken  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
4
 
Installation Instructions  
SB-WM46  
TOOLS REQUIRED FOR INSTALLATION  
1/2" (12.7mm)  
#2  
1/4" (6.4mm)  
3/8" (9.5mm)  
7/16" (11.1mm)  
1/2" (12.7mm)  
PARTS  
B (2)  
[faceplate bracket]  
C (2)  
D (2)  
[short interface  
bracket]  
[long interface bracket]  
A (1)  
[main assembly]  
F (4)  
[backing plate]  
H (1)  
5/32"  
E (1)  
[faceplate]  
G (4)  
[cable cover]  
I (1)  
3/16"  
K (12)  
1/4" x 5/8"  
L (13)  
1/4"  
R (8)  
#8-32 x 3/8"  
M (4)  
1/4"  
Q (1)  
5/16"  
N (1)  
1/8"  
P (1)  
1/4"  
J (1)  
7/32"  
X (4)  
V (4)  
#10-32 x 1 1/8"  
W (4)  
[spacer]  
Y (4)  
3/8"  
3/8" x 2 1/2"  
T (4)  
[cover plate]  
S (4)  
[concrete anchor]  
5
 
SB-WM46  
Installation Instructions  
Concrete Installation  
ASSEMBLY and INSTALLATION  
Install Arm Assembly/Wall Plate to Wall  
Wood Stud Installation  
WARNING: Failure to provide adequate structural strength  
for this component can result in serious personal injury or  
damage to equipment! It is the installer’s responsibility to  
make sure the structure to which this component is attached  
can support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the  
component.  
WARNING: Failure to provide adequate structural strength  
for this component can result in serious personal injury or  
damage to equipment! It is the installer’s responsibility to  
make sure the structure to which this component is attached  
can support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the  
component.  
IMPORTANT ! : The SB-WM46 mounts are designed to be  
mounted to an 8" concrete wall.  
1. Level wall plate and mark locations of pilot holes. (See  
Figure 2)  
IMPORTANT ! : The SB-WM46 mounts are designed to be  
mounted to a 2" x 4" wood studs (16" on center) wall.  
2. Drill 3/8" (9.5mm) diameter holes into concrete. (See Figure  
2)  
1. Level arm assembly/wall plate (A) and mark locations of  
pilot holes. (See Figure 1)  
3. Install anchors (S) into holes. (See Figure 2)  
2. Drill 1/4" (6.4mm) diameter pilot holes into wood supports.  
(See Figure 1)  
CAUTION: Do not overtighten lag screws (X)!  
3. Install 3/8 X 2 1/2" lag screws (X) through flat washers (Y),  
arm assembly/wall plate (A), into wood supports. (See  
Figure 1)  
4. Install 3/8 x 2 1/2" lag screws (X) through flat washers (Y),  
wall plate (A), into anchors (S). (See Figure 2)  
1
x 4  
1
x 4  
x 4  
2
1/4" (6.4mm)  
(A)  
x 4  
2
3/8" (9.5mm)  
(Y) x 4  
(S) x 4  
3
(Y) x 4  
3
(X) x 4  
9/16" (14.3mm)  
4
(X) x 4  
9/16" (14.3mm)  
Figure 1  
Figure 2  
6
 
Installation Instructions  
SB-WM46  
Cover Plate Installation  
1. Install four cover plates (T) using four 10-32 x 1 1/8" Phillips  
pan machine screws (V) and four spacers (W). Insert screw  
into cover plate and add the spacer before inserting the  
cover plate tab into the arm assembly/wall plate. (See  
Figure 3)  
x 4  
2
Place tab  
into slot  
(T) x 4  
(W) x 4  
Figure 4  
(46" or 55" models)  
level with top of washers  
Figure 3  
Installing Interface Brackets to Display  
1. Place display face down on a soft, non-abrasive surface.  
2. Remove four sets of bolts and washers that were shipped  
attached to the back of the display. Set hardware aside for  
re-use. (See Figure 4)  
WARNING: The bolts and washers are designed to be  
permanent fixtures on the television. Never remove the bolts  
or washers except for installation of the wall mount! Always  
replace bolts immediately. Installing the television without the  
bolts and washers may result in serious personal injury and/  
or damage the television!  
(D) x 2  
just above rubber sealing gasket  
(65" models)  
level with top of washers  
3. Place interface brackets (C or D) on the back of the display  
so that they align with the holes on the display. Use  
removed screws and washers to loosely attach interface  
brackets to display. (See Figure 5)  
NOTE: Use short brackets (D) if installing to 46" or 55" models  
and long interface brackets (C) if installing to 65"  
models.  
4. Align bottom of the brackets with rubber sealing gasket and  
the top of the brackets with the top of the washer. (See  
Figure 5)  
(C) x 2  
just above rubber sealing gasket  
Figure 5  
7
 
SB-WM46  
Installation Instructions  
5. Use four removed screws and washers to secure interface  
brackets (C or D) to back of display. (See Figure 6)  
7/16" (11.1mm)  
(M) x 4  
2
(65" model shown)  
x 4  
5
(L) x 4  
(K) x 4  
2
(C or D) x 2  
Figure 8  
Figure 6  
Install Faceplate Brackets to Faceplate  
Install Faceplate to Display  
1. Align faceplate brackets (B) with interface brackets (C or D),  
aligning the middle thumb screw on bottom of display with  
the faceplate bolt. (See Figure 9) and (See Figure 10)  
1. Align faceplate brackets (B) with faceplate (E) and slide into  
position. (See Figure 7)  
faceplate bolt  
1
1
(B) x 2  
(E)  
middle thumb screw  
Figure 7  
Figure 9  
2. Using hex key (H), install four 1/4 x 5/8" button head cap  
screws (K) through four 1/4" washers (L), faceplate (E),  
faceplate brackets (B), into four 1/4" nuts (M). Tighten  
securely. (See Figure 8)  
8
 
Installation Instructions  
SB-WM46  
(F) x 4  
1
(L) x 8  
(B) x 2  
(K) x 8  
2
Figure 10  
2. Using hex key (H), install eight 1/4 x 5/8" screws (K) through  
eight 1/4" washers (L) and faceplate brackets (B) into four  
backing plates (F). Tighten securely. (See Figure 10)  
1
Display Installation  
WARNING: Exceeding the weight capacity can result in  
serious personal injury or damage to equipment! It is the  
installer’s responsibility to make sure the combined weight of  
all components located between the SB-WM46 up to (and  
including) the display does not exceed 150 lbs (68 kg).  
(E)  
1/2" (12.7mm)  
(Q)  
2
1. Align slots on upper portion of faceplate (E) with tabs on  
upper portion of arm assembly (A). Lower display into  
place, pivoting threaded stud on faceplate (E) into slot on  
arm assembly (A). (See Figure 11)  
2. Install spacer (N), washer (P), and nut (Q) onto threaded  
stud. Tighten securely. (See Figure 11)  
(A)  
(N)  
(P)  
Figure 11  
9
 
SB-WM46  
Installation Instructions  
Extension and Swivel Tension  
Cable Management  
WARNING: Excessive loosening or tightening of  
adjustment screws can result in serious personal injury or  
damage to equipment!  
CAUTION: Ensure that adequate cable slack exists for  
movement of display, and that cables will not be pinched by  
installation of covers (G) or screws (R).  
1. Using hex keys (I, J), loosen or tighten adjustment screws  
as required to achieve desired tension. (See Figure 14)  
1. Carefully insert cables into cavities located in lower portions  
of mount arms. (See Figure 12)  
2. Install each cover (G) with two screws (R). (See Figure 12)  
1
1
(G) x 4  
(R) x 8  
2
1
9/16" (14.3mm)  
Figure 12  
Adjustments  
Pitch  
1. Loosen pitch adjustment knob. (See Figure 13)  
2. Tilt display to desired angle (-15° to +15°). (See Figure 13)  
3. Tighten pitch adjustment knob. (See Figure 13)  
1
-15°  
Figure 14  
2
0°  
3
+15°  
Figure 13  
10  
 
Installation Instructions  
SB-WM46  
11  
 
SB-WM46  
Installation Instructions  
SunBriteTV, LLC  
2001 Anchor Court  
Thousand Oaks, CA 91320  
866-357-8688  
8800-002156 Rev00  
04/12  
 

Shuttle Computer Group Server KD21 User Manual
SIIG Network Card EVTEK 5103 User Manual
Sonance Speaker VP65R User Manual
Sony Laptop PCG FX190 User Manual
Sony Personal Computer Vaio Series User Manual
Sony Projector VPL PX15 User Manual
Sony VCR GV D1000E User Manual
Southbend Electric Steamer ECX 2S User Manual
Sunbeam Water Dispenser WF6000 User Manual
System Sensor Smoke Alarm DH200RPL User Manual